Lip Nurit Assistance

Your terminal can do 4 functions SALE, VOID, BATCH, and BRIDGE UPLOAD

SALE

PROMPTS	YOUR INPUT
CREDIT SALE ACCOUNT...	PYMT MODE PYMT MODE on 2060,2080,2085 models ENTER PYMT on 3000 & above until Terminal responds with CHECK SALE AMOUNT or CHECK CONVERSION AMOUNT
CHECK CONVERSION AMOUNT	Amount Enter the Dollar amount of the check. Terminal may say CHECK SALE AMOUNT instead of CHECK CONVERSION AMOUNT
SWIPE CHECK / ENTER ACCOUNT	Ensure check is filled in and signed prior to swiping through check reader. Swipe check through reader. If you have an RDM 6000 the check goes in face up with the account number on the right. For all others the check goes in left hand slot with the face of the check facing right and the numbers on the bottom. Check reader light should blink on & off. If it turns red try again.
ENTER ID	D.L. Key in customer's the drivers license. When entering a drivers license and there are letters, press the number key that has the letter and then press the ALPHA COPY key to convert the number to the letter.
STATE CODE	State Code Key in the state code. Use the table below for the proper state code number. You may also enter the 2 letter abbreviation instead of the state codes given.
SPECIFIC INFO or REFERENCE NUMB	ENTER Press ENTER if this is displayed.
FINALIZE	See the table labeled 'Terminal Responses'. Ensure the terminal receipt is filled in and signed.

STATE CODES

Alabama 10	Alaska 12	Arizona 14	Arkansas 16	California 18	Colorado 20
Connecticut 22	Delaware 24	Florida 26	Georgia 28	Hawaii 30	Idaho 32
Illinois 34	Indiana 36	Iowa 38	Kansas 40	Kentucky 42	Louisiana 11
Maine 13	Maryland 15	Massachusetts 17	Michigan 19	Minnesota 21	Mississippi 23
Missouri 25	Montana 27	Nebraska 29	Nevada 31	New Hampshire 33	New Jersey 35
New Mexico 37	New York 39	No. Carolina 41	No. Dakota 43	Ohio 44	Oklahoma 45
Oregon 46	Pennsylvania 47	Rhode Island 48	So. Carolina 49	So. Dakota 50	Tennessee 51
Texas 52	Utah 53	Vermont 54	Virginia 55	Wash. DC 56	Washington 57
W. Virginia 58	Wisconsin 59	Wyoming 60

TERMINAL RESPONSES

RESPONSE	MEANING
AUTH NUM xxxxxxG or APPROVED xxxxxxG	The transaction is converted to a debit and guaranteed predicated on compliance. Ensure all documents are complete. 1 Checks are filled out. 2 Receipts are complete.
AUTH NUM xxxxxxV or APPROVED xxxxxxV	The transaction is converted to a debit but not guaranteed. Ensure all documents are complete. 1 Checks are filled out. 2 Receipts are complete.
NO ACH xxxxV	The transaction was not converted to a debit REASONS
DECLINED	Transaction rejected. Do not accept check. REASONS
ALL OTHERS	If you received a response not listed here it may be an error. See the page labeled 'Error Definitions' for your terminal configuration.

VOID A SALE

PROMPTS	YOUR INPUT
CREDIT SALE ACCOUNT...	PYMT MODE PYMT MODE until Terminal responds with CHECK SALE AMOUNT or CHECK CONVERSION AMOUNT
CHECK CONVERSION AMOUNT	VOID VOID key. Terminal should say CHECK VOID AMOUNT. Enter the amount of the check.
SWIPE CHECK / ENTER Account	Swipe check through reader. If you have an RDM 6000 the check goes in face up with the account number on the right. For all others the check goes in left hand slot with the face of the check facing right and the numbers on the bottom. Check reader light should blink on & off. If it turns red try again. Terminal should respond with 'VOID ACCEPTED'. If it does not please contact Global Check.

BATCH Not required

PROMPTS

YOUR INPUT

CREDIT SALE ACCOUNT...
BATCH
(2080/2085) the BATCH key. All others, FUNCTION & 6

BATCH ALL ?

ENTER
ENTER. Terminal should batch out and print a report. The report will show each check attempt. Even if the check was not converted its amount will appear on this report. Do not use this total as a basis for your account balance. Use the transaction receipts instead or this

This is only required if you have a Magtek Imager.
This procedure transfers the check images to our server.

BRIDGE UPLOAD

PROMPTS

YOUR INPUT

CREDIT SALE ACCOUNT...

(All but 2085)Press the FUNCTION key and number 6 (2085 only) Press BATCH

1.BATCH TO HOST
2.BRIDGE UPLOAD

Press 2 and ENTER. Terminal should dial out and transfer the check images.

Owned by David Homoki , Dave Homoki